WaterMark certification

New ABCB guide helps plumbers check Lead Free WaterMark product compliance

When a plumber opens a carton on site, the question is about the fitting in their hand. Is this particular model certified for drinking water, and can it be installed on this job? On 16 November, the Australian Building Codes Board (ABCB) released a communications pack to help the industry answer those questions as Australia moves to Lead Free plumbing products.

Published 16 November 2026

CSi and Lead Free WaterMark logos beside a mixer tap, fittings and a valve

The communications pack includes an article and social media messages that suppliers and plumbing businesses can share. At Certification Solutions International (CSi), we see a practical use for it at the trade counter: give the installer the guidance alongside the model number and certificate for the product they are buying.

Resources for plumbing practitioners

Read the ABCB communications pack for plumbing practitioners

What the mark tells you

For products covered by the requirement, copper alloy in contact with drinking water must have a weighted average lead content of no more than 0.25%. From 1 May 2026, affected products must meet the Lead Free requirements for manufacture and certification. Installation dates vary, which matters when a merchant still has earlier stock on the shelf.

Start with the model ID on the carton. Find it in the WaterMark Product Database, then match it to the current certificate and product schedule. Check that the exact model, its intended use and its Lead Free coverage agree. If the sales catalogue uses a different code, ask the supplier to show how the two codes correspond before accepting a substitute.

Look up a model in the WaterMark Product Database

Which installation date applies to the job?

For a merchant supplying both sides of the NSW–Victoria border, even the question to ask is different. In Victoria, ask when plumbing installation began. In NSW, ask when the individual fitting will be installed. Here is the published position for affected products as at 16 November 2026.

Victoria

Use Lead Free certified models where plumbing installation commenced on or after 1 May 2026. An earlier building permit, design or contract does not change that trigger.

Building and Plumbing Commission

New South Wales

Through 30 April 2028, existing stock may be installed if its WaterMark licence is current and the model remains listed. From 1 May 2028, each affected fitting installed must be Lead Free certified, even on a project already under way.

Building Commission NSW

Queensland

The QBCC gives suppliers and installers until 1 May 2028 to transition. During that period, check that each product is authorised for its intended use before supplying or installing it.

QBCC guidance

Western Australia

Existing WaterMark-certified stock may be installed through 30 April 2028. From 1 May 2028, the Lead Free requirement covers both new installations and replacement fittings in existing drinking water systems.

Industry Bulletin 171

South Australia

The Office of the Technical Regulator published a 1 May 2026 enforcement date. Its notice predates the national extension. Specify Lead Free certified models now. Before using older stock, seek a ruling from the OTR on 1300 760 311.

SA plumbing advisory note

Tasmania, Australian Capital Territory and Northern Territory

The ABCB gives 1 May 2028 as the national installation date and allows local variations. We could not verify a local installation deadline for these three jurisdictions. Specify a Lead Free certified model now. If relying on older stock, confirm eligibility with CBOS in Tasmania, Access Canberra in the ACT or NT Building Advisory Services in the Northern Territory.

ABCB transition direction

A direct line to Rob at CSi

CSi is a JASANZ accredited, ABCB, licensed WaterMark certifier. Robert Hardgrove, our Client Manager for WaterMark Certification, brings more than 20 years in the Australian plumbing-products industry to the questions behind a certificate. A supplier may need to match a merchant’s stock code to a certified model. A manufacturer may want to change the alloy in a valve body and understand what evidence CSi needs before the revised valve can carry the mark.

When you contact CSi about WaterMark, you can speak directly with Rob. Whether you’re exploring certification for the first time or making a change to an existing product, Rob takes the time to understand your business, talk through your options and explain the next step. Call or email him to start the conversation.

Call CSi on +61 2 9728 7608

Email Rob at robert@csi-certification.com
Contact Robert Hardgrove about Lead Free WaterMark products
Robert Hardgrove, Client Manager for WaterMark Certification

Discuss your certification needs with CSi.

Tell us about your product, organisation, intended market and the outcome you need.

Contact CSi